From Wikihowto

---

Warning: This page is incomplete, use this article with caution. Please help finish it

The technique for building a transformer and inductor are the same, however designing them are different.

** If you are interested in a quick design of an inductor or transformer, with out the details or precision follow the red double astrix, '**'

Contents 1 Variables, Units, and Acronyms 2 Design 2.1 Selecting the size and type of core 2.1.1 Core size 2.2 Selecting the wire gauge 2.2.1 Resistive Loss 2.2.2 Fill-factor 2.3 Inductor 2.3.1 Advanced Inductor design 2.4 Transformer 3 Construction 3.1 Winding 3.1.1 ferrite core, bobbin 3.1.2 Toroid 3.1.3 Laminated iron core 3.1.4 Air core 4 References

[edit] Variables, Units, and Acronyms

You have to keep track of units during design. Its easy to get mixed up. Wire gauges are generally in non-metric, as well as some other variables. For the most part keep units in metric and distances in centimeters

The following quantities are specified, using the units noted:

• Universal constants
  • Permittivity of free space (Wb A^-1 m^-1)
    • (Wb A^-1 m^-1)

• Wire variables:
  • , Wire resistivity (Ω-cm)
  • , Total RMS winding currents (A)
  • , Peak magnetizing current (A)
  • , Max RMS current, worst case (A)
  • , Allowed copper loss (W)
  • , Cross sectional area of wire (cm²)

• Xformer/inductor design parameters
  • , turns (turns)
  • , Magnetizing inductance (for an xformer) (H)
  • , Inductance (H)
  • , Winding fill factor (unitless)
  • , Core maximum flux density (T)

• Core parameters
  • EC35, PQ 20/16, 704, etc, Core type (mm)
  • , Geometrical constant (cm⁵)
  • , Geometrical constant (cm^x)
  • , Cross-sectional area (cm²)
  • , Window area (cm²)
  • , Mean length per turn (cm)
  • , Magnetic path length (cm)
  • , or , Air gap length (cm)
  • , Permittivity (Wb A^-1 m^-1)
  • , Relative Permittivity (unitless)
    • 

Acronyms

• RMS: root-mean-squared - (where denotes the arithmetic mean)
• MLT: mean length turn
• AWG: American wire gauge

[edit] Design

[edit] Selecting the size and type of core

This is a very very basic way to choose a core. The type of core has allot to do with the frequency, current, and power. The size and type of the core has to do with core loss, power loss in the core.

• Low frequency such as 60-120Hz should use laminated core**
• High frequency 1kHz-1MHz should use a ferrite core.**

The size of the core depends on the power of the transformer, and expected power loss in the core (core loss).

[edit] Core size

Be careful about units

• Copper (wire) resistivity
  • 
  • 
    • Transformers, inductors can get warm, and hot so it may not be room temp
• , Max core magnatizing flux density (T)
• , Max RMS current, worst case (A)
• , Winding fill factor (unitless)
• , Inductance (H)

The core

• When selecting a core you have the following parameters
  • , Mean length per turn (cm)
  • , Core cross sectional area (cm²)
  • , Core window area (cm²)
  • , Core geometrical constant (cm⁵)
• Types of Cores wikipedia:Magnetic core

[edit] Selecting the wire gauge

The selection on the wire gauge has to do with the amount of resistance that is acceptable, and if all the turns can fit in the area of the transformer. The size of the transformer can always be increased if more area is needed

[edit] Resistive Loss

Variables in calculating resistance

• , Mean Length per Turn, the average length of wire to complete a full turn (cm)
• , Cross sectional area of wire (cm²)
• , number of turns
• , resistivity of copper, 1.724 10^–6 (Ω-cm)

Measure Mean Length per Turn (MLT). The easy way to measure MLT is to take a wire and wrap it around the core or bobbin, loosely. If you plan on have multiple turns try to make an average loop, but looser to be safe. Measure the wire and thats your MLT. Some cores will give you the MLT in the specification. Keep in mind that the specification is for a fully filled core, but use it to be safe. Always be conservative, and make the length longer.

Number of turns (n) is gotten when you calculate the inductance for an inductor or tuns ration for a transformer.

Cross sectional area of wire (A_w) is based on the size wire you choose, obviously. The size of wire goes on the American wire gauge (AWG)). Wikipedia has a chart of wire gauges with there Area. See wikipedia:American wire gauge.

The equation for resistance is:

Remember to keep you units correct.

[edit] Fill-factor

**Another factor you need to be aware of is will all the turns of wire fit in your core. This is called the fill-factor. If the amount of turns you need with the wire size you need does not fit you can always use a bigger core.

The variables are

• , Window area (cm²)
• , Wire area (cm²)
  • See wikipedia:American wire gauge for wire areas
• , Number of turns
• , Window utilization factor, the fill-factor
  • , must be less than 1
    • Realistic fill-factors
      • 0.5 for simple low-voltage inductor
      • 0.25 to 0.3 for off-line transformer
      • 0.05 to 0.2 for high-voltage transformer (multiple kV)
      • 0.65 for low-voltage foil-winding inductor

So you must follow this equation

For multiple wire types the equation would be

[edit] Inductor

In general inductors use a ferrite core.

Inductance for a coiled bobbin, with a magnetic core

In general you control the inductance by making l an air-gap, which will be very small and μ the permittivity of free space

where

• , number of turns
• , cross section area of the core
• , permittivity of the free space or if no air gap the permittivity of the ferrous material
• , length of the air gap or if no air gap the length of the ferrous materials loop

Inductance for a toroid

where

• , number of turns
• , cross section area of the core
• , permittivity of the free space or if no air gap the permittivity of the ferrous material
• , radius of the toroid (to the center/middle of the ferrous material)

Inductance for a short air core coil

where

• , number of turns
• , radius of the coil
• , length of the coil

[edit] Advanced Inductor design

Nearly full description of Inductor design. Very good, but very technical. Recommended for building inductors in optimizing power, size, losses, and precise inductance.

Chapters from a power electronics course

• Chapter 14 Inductor Design
• Chapter 13. Filter Inductor Design

[edit] Transformer

The base equations for a transformer.

**

**

Transformers have inductance.

In most cases you don't want inductances in a transformer, unless you are using it in a switching converter, or filter. Inductance only has to be a modeled on one side, as . If you transformer has no air gap the inductance will be low, and can be ignored

[edit] Construction

[edit] Winding

There are easy ways to wind a core and there are hard ways. Well semi-easy.

[edit] ferrite core, bobbin

Image of an ER ferrite core inductor

Winding a ferrite core is very easy. You just need to wrap the wire around the bobbin.*

[edit] Toroid

Toroid core

Toroid wound transformer

Needle used for winding a Toroid

If you only need a few windings the solution is simple. Just wind it.

When there are many windings, the easiest way to wind a Toroid is to make a needle like show in the laminated core image. The needle needs to be thinner, and the length of the needle dictates the length of the wire you can wrap without splicing two wires.

Making the needle: **

• Get a soft semi-flexible piece of plastic, or what ever u can find
• Cut it in the shape shown in the image
• poke a hole in the needle to have the wire start at
• Wind your needle
  • Don't make it thicker that the Toroid (obviously)

To wind it: **

• hold one end of the wire
• thread the needle trough the Toroid.
• Wrap it around the torrid
  • Make sure the loops are tight, and close together. Well wrapped loops increase the number of windings you can make.
• Repeat

[edit] Laminated iron core

Image of a transformer being built

A wound transformer with the needle for winding it

Needle used for winding a Laminated iron core

• to be: **

[edit] Air core

• Get a plastic screw
  • Width of the screw being twice the radius of the coil.
  • Thread size to match the number of turns with the length of the coil. It wont be perfect, but you can compress or stretch the coil to the correct length

    Bring the wire and a ruler to the hardware store

[edit] References

• Chapter 14 Inductor Design: very good.
• Chapter 13. Filter Inductor Design: very good
• Electronic Components: very good
• Wikipedia:Transformer_design
• http://www.geofex.com/Article_Folders/xformer_des/xformer.htm
• Core types
  
  
  From HowTo Wiki, a Wikia wiki.
• TI - Magnetics Design 4 - Power Transformer Design - switching power supplies
• Core Selection for Saturating Transformers - core material parameters, design tips, .......